Experience
See some of our best work below.
Projects we’ve designed trusses for, each drawn from its real truss model. Hover over a card to turn the building, or open a project to see its framing up close.
Truss designs we prepared for bids and estimates, shown without project names. Some of these models look incomplete, and that is on purpose: for a bid we sometimes design only part of a building, then use that portion to estimate the rest by the square foot.
Project
6th St. SE
Four-story building with floor trusses on every level and a roof truss system above. Move across the model to turn it.
- Trusses placed
- 2,330
- Unique designs
- 180
- Stories
- 4
- Systems
- Floor, roof
About the project
Sixth Street Phase I, 707 6th Street SE
Charlottesville, Virginia · Affordable multifamily · 2025–2026
Sixth Street Phase I is the first new building in the Charlottesville Redevelopment and Housing Authority's resident-led plan for its Sixth Street site. The four-story building holds 47 one-, two- and three-bedroom affordable homes above a level of parking, along with a community center and on-site management offices.
The truss package covers three framed floors and the roof: 22-inch-deep floor trusses and flat roof trusses with parapet legs built in, all at 16 inches on center, tied into flush LVL beams and LSL rim boards. Much of the work was coordination. Questions about unit demising walls with no support below, framing conflicts in an accessible unit type, blocking connections and roof hangers were worked through with the architect, the engineer of record and the contractor before and during framing.
The design began during our founder's time with Quadd Building Systems, the project's truss supplier, and continued under Shored Design through submittals, revisions and field support.
Project credits
- Truss Supplier
- Quadd Building Systems
- General Contractor
- UrbanCore Construction
- Architect
- Grimm and Parker Architecture
- Structural Engineer
- Dunbar Milby Williams Pittman & Vaughan
- Owner
- Charlottesville Redevelopment and Housing Authority
From the field
Project
South First St. Phase II, Building 7
Building 7 of South First Street Phase II: two floor systems and the roof, brought together from three Paragon models. Move across the model to turn it.
- Trusses placed
- 404
- Unique designs
- 78
- Stories
- 3
- Systems
- Floor, roof
About the project
South First Street Phase Two, Building 7
Charlottesville, Virginia · Affordable multifamily · 2025–2026
South First Street Phase Two replaces 58 older public housing apartments with 113 new affordable homes in 21 buildings, along with a community center, park and playground. It is the second phase of the Charlottesville Redevelopment and Housing Authority's resident-led rebuilding of the site.
Building 7 is a wood-framed building of eight homes over a basement level. Its truss design is shared with Buildings 8 and 9, with a close variant for Building 6. The package is two floor systems and the roof, and it followed the building through several rounds of plan changes: foundation and basement walls moved, stair openings resized, trusses shifted to clear tub drains, ductwork and plumbing, extra dead load added under tiled floors, and overframing added at the roof.
The design began during our founder's time with Quadd Building Systems, the project's truss supplier, and continued under Shored Design through submittals, revisions and field support.
Project credits
- Truss Supplier
- Quadd Building Systems
- General Contractor
- UrbanCore Construction
- Architect
- BRW Architects
- Owner
- Charlottesville Redevelopment and Housing Authority
Project
Mainline Apartments
Apartment community with four building types. Each type shows its two floor systems and roof; pick a type to look at it on its own. Move across the model to turn it.
- Building types
- 4
- Trusses shown
- 4,521
- Stories
- 3
- Systems
- Floor, roof
About the project
Mainline Apartment Homes
Stafford County, Virginia · Multifamily · 2024–2026
Mainline Apartment Homes is a new apartment community on Warrenton Road in Stafford County, just outside Fredericksburg. It was built in two phases: ten three-story breezeway buildings in four building types, with one-, two- and three-bedroom homes, plus a clubhouse, a maintenance building and a mail kiosk.
Each building type has two floor systems and a pitched roof with hips and valleys, and the package also covers the low-slope roofs of the clubhouse and maintenance building. Across both phases that comes to roughly 170,000 square feet of floor trusses and more than 115,000 square feet of roof trusses. Along the way the design settled conflicts between the architectural and engineering drawings on floor truss depth, breezeway beams, fire barrier framing at the roof and the framing over the sprinkler rooms.
The design began during our founder's time with Quadd Building Systems, the project's truss supplier, and continued under Shored Design through submittals, building-by-building layouts and field support.
Project credits
- Truss Supplier
- Quadd Building Systems
- General Contractor
- Clancy & Theys Construction
- Architect
- TS3 Architects
- Structural Engineer
- Speight Marshall Francis
Project
YWCA Building 1
Roof truss system for YWCA Building 1, with hips, valleys and piggyback sections. Move across the model to turn it.
- Trusses placed
- 672
- Unique designs
- 136
- Systems
- Roof
About the project
The Heights, YWCA Apartments Building 1
Highland Springs, Virginia · Affordable housing · 2026
The Heights is YWCA Richmond's new community on North Airport Drive in Highland Springs, east of Richmond. The five-acre site brings together affordable apartments, a Sprout School preschool and townhomes built by the Maggie Walker Community Land Trust. Building 1 is part of the apartments in the first phase.
Shored Design prepared the roof truss design and placement plans for Quadd Building Systems, the project's truss supplier. The roof is pitched, with hips, valleys, piggyback sections and overframing, and drops to low-slope trusses at the mechanical wells. A truss lands on every wall between units, and pre-engineered truss blocking panels sit over the shear walls. Questions about shear blocking, framing over the corridor and design loads were settled with the architect and engineer during submittals.
Project credits
- Truss Supplier
- Quadd Building Systems
- General Contractor
- UrbanCore Construction
- Architect
- Poole & Poole Architecture
- Structural Engineer
- Cates Engineering
- Developer
- Rebkee
- Owner
- YWCA Richmond
Project
Sprout School
Single-story school with a roof truss system over the full building. Move across the model to turn it.
- Trusses placed
- 297
- Unique designs
- 71
- Stories
- 1
- Systems
- Roof
About the project
YWCA Sprout School at The Heights
Highland Springs, Virginia · Early childhood education · 2026
The Sprout School is the preschool at The Heights, YWCA Richmond's new community in Highland Springs. The single-story building will serve families living on the site and in the neighborhoods around it.
Shored Design prepared the roof truss design and placement plans for Quadd Building Systems, the project's truss supplier. The roof is nearly flat: 30-inch-deep trusses at 24 inches on center with a quarter inch of slope per foot, parapet framing built into the trusses, and shear trusses running continuously over the corridor walls. Ductwork, lighting and access panels all share the roof space, so most of the effort went into coordinating truss locations with the mechanical trades, along with an RFI to confirm roof loads before the trusses were built.
Project credits
- Truss Supplier
- Quadd Building Systems
- General Contractor
- UrbanCore Construction
- Architect
- Poole & Poole Architecture
- Structural Engineer
- Cates Engineering
- Owner
- YWCA Richmond
Project
Kiddie Academy
Single-story childcare building with a roof truss system over the full building. Move across the model to turn it.
- Trusses placed
- 372
- Unique designs
- 81
- Stories
- 1
- Systems
- Roof
About the project
Kiddie Academy of Gambrills
Gambrills, Maryland · Child care · 2026
Kiddie Academy of Gambrills is a new single-story child care center of roughly 15,000 square feet on St. Stephens Church Road in Anne Arundel County. It broke ground in July 2026.
Shored Design prepared the roof truss design and placement plans for Quadd Building Systems, the project's truss supplier. The low-slope roof is framed with 30-inch-deep trusses at 24 inches on center, with parapet posts built into the trusses and connections to beams set flush within the roof depth. The design was revised after the first submittal to follow changes in the building's dimensions.
Project credits
- Truss Supplier
- Quadd Building Systems
- Contractor
- Construction Services & Supply
- Architect and Engineer
- Jarmel Kizel Architects and Engineers
Project
3600 Grove Ave.
Six-story apartment building in Richmond's Museum District: five wood-framed levels over a concrete first level, wrapped around a six-level precast parking deck. The model shows floor trusses on four levels and the roof, built from the truss design files. Move across the model to turn it.
- Trusses placed
- 9,419
- Unique designs
- 1,544
- Stories
- 6
- Units
- 253
Parking deck and first level shown in outline for context
About the project
Ellison Museum District, 3600 Grove Avenue
Richmond, Virginia · Multifamily · Completed 2026
Rising six stories in the heart of Richmond's Museum District, the Ellison Museum District is a 253-unit luxury apartment community occupying a full city block at 3600 Grove Avenue. At roughly 404,000 square feet of wood-frame construction on a 2.2-acre site, it is one of the largest multifamily projects delivered in the neighborhood in decades, and a showcase for what engineered wood construction can achieve at scale.
The truss designs for the project were completed by Shored Design's founder during his time with Quadd Building Systems, the project's truss supplier. That work laid the foundation for the design practice Shored Design carries on today. Designing for a wood-frame building of this size meant coordinating truss layouts across a large, complex footprint while meeting the structural demands of six-story construction, all while keeping every component practical to manufacture and efficient to set in the field. The design presented many unique design challenges, such as designing girder trusses for carried levels above, specifying custom-skewed hardware, and in-depth trade coordination over several months.
Developed by Flournoy Development Group and designed by Dynamik Design, the community features a resort-style courtyard and pool, rooftop lounge, fitness center, co-working spaces, an on-site market, and a precast parking deck. Construction began in early 2024, and residents began moving in before the end of 2025.
Project credits
- Truss Supplier
- Quadd Building Systems
- Framing
- Ace Carpentry
- General Contractor
- Clancy & Theys Construction
- Developer
- Flournoy Development Group
- Architect
- Dynamik Design
From the field
Project
Apartment building, L-shaped plan
Multi-story apartment building with floor systems and the roof designed for a bid. Move across the model to turn it.
- Trusses placed
- 2,625
- Unique designs
- 308
- Systems
- Floor, roof
Project
Apartment building, long bar plan
Multi-story apartment building with floor systems and the roof designed for a bid. Move across the model to turn it.
- Trusses placed
- 2,361
- Unique designs
- 266
- Systems
- Floor, roof
Project
Apartment building, two wings
Multi-story apartment building with floor systems and the roof designed for a bid. Move across the model to turn it.
- Trusses placed
- 1,198
- Unique designs
- 188
- Systems
- Floor, roof
Project
Apartment building, corridor plan
Multi-story apartment building with floor systems and the roof designed for an estimate. Move across the model to turn it.
- Trusses placed
- 1,072
- Unique designs
- 194
- Systems
- Floor, roof
Project
Residential community
Community designed for a bid, with the floor and roof packages shown separately. Move across the model to turn it.
- Trusses placed
- 2,957
- Unique designs
- 469
- Systems
- Floor, roof
Project
Custom residence and pool house
Large custom home with a separate pool house, designed for a bid: floor trusses over the first level and roofs of hips, valleys and gables. Move across the model to turn it.
- Trusses placed
- 811
- Unique designs
- 180
- Stories
- 2
- Systems
- Floor, roof